* This product is printed once the order is placed and usually ships within 7-13 days.*
Our industry-leading frame protection is easy to install and provides durable protection against scratches, chips, shuttle rub, and whatever else is thrown it's way.
Our universal kit is designed to fit all bikes and sizes and comes with 6 easy-to trim pieces for toptube, downtube, chainstays, and seatstays. Designed to fit XL frames, each piece can be trimmed down to desired length and width.
Dimensions:
Toptube & Downtube: 22.5" x 3.2"
Chainstays & Seatstays: 13" x 1.4"
Cool, calm, and collected - Dye Hard is a subdued collection that combines an array of saturated pigments with grungy textures.
1. Clean your bike thoroughly and wipe frame with isopropyl alcohol. Wash your hands to ensure you don’t leave any dirty fingerprints under the glue. If it’s below 50 degrees Fahrenheit, roll your bike indoors for the following steps.
2. Grab a pair of scissors or an exacto knife. All pieces are designed for larger frames and will likely need to be trimmed before mounting. Before removing the backing, line each piece up to your frame and mark any pieces that need to be shortened or thinned. Trim from the bottom and make sure to round any hard edges (this will help it from pulling up over time).
3. Remove backing and center the guard where you want it. Make sure to do any repositioning before applying pressure. Once you’re happy with the position, lightly tack the center of the guard from top to bottom. Apply pressure from center to sides, pushing out any air/bubbles with your thumbs. We don’t recommend wet application with our material.
Pro Tips: • Lightly blasting each piece with a hairdryer or heat gun before applying pressure warms the adhesive and makes for an easier application. • If you have issues wrapping guard around curves, add additional relief cuts where needed. • To avoid leaving finger prints on transparent Frame Keepers, wet your finger tips if you need to reposition the guard. • Use a vinyl squeegee tool to help eliminate bubbles during the application process. • Get clever with your scrap pieces! Throw them on the seat tube, top of the downtube, or wherever you may experience cable rub.
Removal:
ALWAYS use heat when removing Frame Keeper to ensure clean removal. We also recommend using heat when repositioning the Frame Keeper during application.
HOW WILL MY KIT FIT?
ROAD / GRAVEL
One kit provides fuller coverage on the smaller tubes of road and gravel bikes.
Mountain
One kit provides mid coverage on the larger tubes of most mountain bikes.
Mountain - 2 kits
Two kits provide fuller coverage on mountain bikes. Recommended for e-bikes.
Quality Materials
High tack, flexible and easy-to-install material that conforms to the curves and contours of the frame while providing ample protection. At 10 mil thick it's the goldilocks thickness between durability and conformability.
High resolution graphics digitally printed with industry-leading equipment and topped with ultra-thick UV and scratch resistant laminate.
You might also like
Customer Reviews
Overall rating: 4.7 / 5 from 27 reviews.
I've used other products and this material seemed the easiest to install. I think it looks great!
I suppose if I had a complaint it would be the Ground Keeper logo on the top tube piece, because it was not possible to cut that segment to go above my emtb top tube display without cutting the logo in half. Very minor issue, 5 stars. 🤘
I've used other protective wraps in the past, but Groundkeeper wrap works so much easier and better than anything I've done before. It also looks awesome!
I think they look great went on easy but would have loved if they were more fit for the frame size cutting to size is definitely a little tricky I hope I never have to replace pulling the factory applied ones off and getting all the adhesive off the frame before I could apply these was a 3 day project
Very easy to use and looks great. Was even able to take it off after I realized it wasn't where I wanted it to be. (Not advisable though as it got a couple of air bubbles!)
Since I just got this bike, I figured I'd try this to see what all the fuss was about. Didn't want to shell out $125 for a Decoy specific wrap and got this. I cut the down-tube strip in half to use along the sides. I think it turned out well overall for my first one. Good enough for some basic protection, not gonna win any contests
Definitely cool looking! Everyone thinks it’s camp because of my bike color but it still looks sweet. Kind of easy to install. I had to cut all of them but it was cool to have extra to put in places I needed.